锥齿轮齿面磨削烧伤自动检测装置设计
CSTR:
作者:
作者单位:

1. 北京工业大学机械工程与应用电子技术学院北京100124;2. 北京工业大学 北京市精密测控技术与仪器工程技术研究中心北京100124

中图分类号:

TH132.41

基金项目:

国家重大科学仪器设备开发专项(2013YQ590395)资助


Design of automatic detection device for grinding burn of bevel gear tooth surface
Author:
  • Lin Jiachun

    Lin Jiachun

    1.College of Mechanical Engineering and Applied Electronics Technology, Beijing University of Technology, Beijing 100124, China; 2.Beijing Engineering Research Center of Precision Measurement Technology and Instruments, Beijing University Technology,Beijing 100124, China
    在期刊界中查找
    在百度中查找
    在本站中查找
  • Zhang Linghao

    Zhang Linghao

    1.College of Mechanical Engineering and Applied Electronics Technology, Beijing University of Technology, Beijing 100124, China; 2.Beijing Engineering Research Center of Precision Measurement Technology and Instruments, Beijing University Technology,Beijing 100124, China
    在期刊界中查找
    在百度中查找
    在本站中查找
  • Shi Zhaoyao

    Shi Zhaoyao

    1.College of Mechanical Engineering and Applied Electronics Technology, Beijing University of Technology, Beijing 100124, China; 2.Beijing Engineering Research Center of Precision Measurement Technology and Instruments, Beijing University Technology,Beijing 100124, China
    在期刊界中查找
    在百度中查找
    在本站中查找
Affiliation:

1.College of Mechanical Engineering and Applied Electronics Technology, Beijing University of Technology, Beijing 100124, China; 2.Beijing Engineering Research Center of Precision Measurement Technology and Instruments, Beijing University Technology,Beijing 100124, China

  • 摘要
  • | |
  • 访问统计
  • | |
  • 相似文献 [20]
  • | | |
  • 文章评论
    摘要:

    针对高性能锥齿轮在进行磨削加工后齿面磨削烧伤检测问题,研制了锥齿轮齿面磨削烧伤自动检测装置,该装置由机械结构、巴克豪森噪声检测模块和检测软件组成。检测装置完全依靠锥齿轮试验机自身的机械系统与电气系统以实现自动检测;其机械结构与被测锥齿轮共用夹具,通过引入柔性轴的设计,可满足多种锥齿轮的检测要求,并可将弧齿锥齿轮的检测过程由六轴联动简化为四轴联动;采用AST公司的RollScan350磁弹仪采集被测锥齿轮的巴克豪森噪声信号,经由上位机检测软件分析处理,对其烧伤情况作出评定。实验结果验证了该检测装置具有较高的重复性,对于齿轮生产中的质量控制有重要意义。

    Abstract:

    Aiming at the detection of grinding burn of high performance bevel gear after grinding, the automatic detection device for grinding burn of bevel gear tooth surface is developed. The detection device is composed of mechanical structure, Barkhausen noise detection module and test software. The detection device completely relies on the mechanical system and electrical system of bevel gear tester to realize automatic detection. The mechanical structure shares fixture with gears, by introducing flexible shaft design, which can meet the requirements of a variety of bevel gear detections. And the detection process of spiral bevel gear can be simplified. AST RollScan350 magnetic elastic instrument is employed to collect the Barkhausen noise signal of measured bevel gear. The collected signals are analyzed using detection software run in the host computer. Experimental results indicate the high repeatability of the detection device for quality control in gear production.

    参考文献
    引证文献
    网友评论
    网友评论
    分享到微博
    发 布
引用本文

林家春,张凌浩,石照耀.锥齿轮齿面磨削烧伤自动检测装置设计[J].仪器仪表学报,2017,38(5):1176-1183

复制
分享
文章指标
  • 点击次数:2170
  • 下载次数: 3903
  • HTML阅读次数: 0
  • 引用次数: 0
历史
  • 在线发布日期: 2017-07-10
文章二维码