可见光粗跟踪成像镜头光机结构设计
DOI:
作者:
作者单位:

中国科学院长春光学精密机械与物理研究所长春130033

作者简介:

通讯作者:

中图分类号:

TH753.3TH761.7

基金项目:

国家自然科学基金(11403023)项目资助


Optomechanical structure design of visible light rough tracking and imaging lens
Author:
Affiliation:

Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033, China

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    为某在研地基光学望远镜设备设计了300 mm口径的可见光粗跟踪成像镜头的光机结构。采用弯月形结构优化使主镜重量减少了41.2%。针对传统胶粘接固定结构的不足提出了采用弹性压紧方式的主镜支撑结构,采用Patran有限元仿真软件对不同倾角、不同温度状态下,带支撑的主镜面形精度进行了分析;制定了装调方案,室内采用Zygo干涉仪检测带支撑的主镜面形精度检测结果为0.04λ(RMS),可见光波长λ的设计参考值为0.633 μm,长焦端和短焦端的系统波像差均为0.132λ(RMS);室内采用平行光管进行星点检验、分辨率检验和外场对北极星成像试验结果显示,系统成像质量满足设备要求;验证了主镜支撑结构和镜头光机结构设计的合理性,为研制同类型镜头的光机结构提供了设计依据和技术途径。

    Abstract:

    The optomechanical structue of 300mm aperture visible light rough tracking and imaging lens was designed for a certain developing ground base optical telescope. The concave mirror structure contouring the rear surface was optimized and the primary mirror weight was reduced by 41.2%. Aiming at the deficiencies of the conventional cementing structure, the new primary mirror supporting structure with elastic compression was adopted. The Patran finite element method (FEM) simulation software was adopted to analyze the accuracy of the primary mirror surface figure with supporting structure at different tilt angle positions and different temperatures. The installation and test scheme was designed, Zygo interferometer was used to test the accuracy of the primary mirror surface figure with supporting structure indoor; and the test result of the surface figure is 0.04λ (RMS), the design reference value of the visible light wave length λ is 0.633 nm and the wavefront aberrations of the optical system both for longfocus lens and shortfocus lens are 0.132λ (RMS). The test results of the indoor collimator star test, resolution test and outdoor polaris imaging test indicate that the system imaging quality meets the telescope requirement. The results verify the reasonability of the new primary mirror supporting structure and lens optomechanical structure design, which provides the design basis and technical path for developing the optomechanical structure of similar lenses.

    参考文献
    相似文献
    引证文献
引用本文

王槐,代霜,范磊,赵勇志.可见光粗跟踪成像镜头光机结构设计[J].仪器仪表学报,2017,38(5):1190-1197

复制
分享
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2017-07-10
  • 出版日期: